Ubiquiti airFiber 5U Guide de l'utilisateur

5 GHz Carrier Backhaul RadioModel: AF-5XDATAMGMTGPSLINKDATAMGMTGPSLINK

airFiber ConfigurationThe instructions in this section explain how to access the airFiber Configuration Interface and configure the following settings

4. The login screen will appear. Enter ubnt in the Username and Password fields. Select your Country and Language. You must agree to the Terms of Use

8. Configure the Basic Wireless Settings:a. For one AF-5X, select Master as the Wireless Mode. For the other AF-5X, keep the default,Slave.b. Ente

12. In-Band Management is enabled by default, so each airFiber radio must have a unique IP Address. (If the airFiber radios use the same IP Address, y

Hardware InstallationInstall a Ground Wire1. Remove the nut from the Ground Bonding Point located on the back of the AF-5X.Ground Bonding Point2. At

Mount to an AntennaThe AF-5X can be mounted to an airFiber X antenna or an airFiber X converted RocketDish. The airFiber X Antenna (AF-5G30-S45) is sh

2. Attach the RF cables from the antenna feed to the RF connectors on the AF-5X in this combination: + 45° to Chain0 and - 45° to Chain 1.3. Attach

4. Attach the protective shroud. a. Align the hash mark on the top of the shroud with the notch on the dish antenna. b. Rotate the shroud clockwise

Mount the External GPS AntennaLocate a mounting point that has a clear view to the sky, and is above and as far away as possible from the AF-5X.1. At

Connecting Power over Ethernet1. Lift the release latch on the bottom of the AF-5X and slide the Port Cover off. 2. Connect an outdoor, shielded Eth

IntroductionThank you for purchasing the Ubiquiti Networks® airFiber® 5GHz Carrier Backhaul Radio. This Quick Start Guide is designed to guide you th

3. Connect the other end of the cable from the DATA port to the Ethernet port labeled POE on the airFiber PoE Adapter.WARNING: Use only the included

Mount the PoE Adapter (Optional)1. Remove the Mounting Bracket from the adapter by sliding the bracket downward.2. Place the Mounting Bracket at the

Surge ProtectionFor added protection, install two surge suppressors, such as the Ubiquiti Ethernet Surge Protector, model ETH-SP, at the end of each l

AlignmentTips• To accurately align the airFiber radios for best performance, you MUST align only one end of the link at a time.• You may need to use

b. Loosen the six elevation bolts, and use the hex nut on the elevation rod to adjust the elevation.Note: Do NOT make simultaneous adjustments on the

4. Slave Aim the Slave at the Master to achieve the strongest signal level on the Master.Note: Refer to the Signal LEDs section for details on the s

Installer Compliance ResponsibilityDevices must be professionally installed and it is the professional installer’s responsibility to make sure the dev

SpecificationsairFiber AF-5XDimensions 224 x 82 x 48 mm (8.82 x 3.23 x 1.89")Weight 0.35 kg (0.77 lb)RF Connectors (2) RP-SMA Weatherproof (CH0,

www.ubnt.comOnline ResourcesSupport support.ubnt.comCommunity community.ubnt.comDownloads downloads.ubnt.com© 2015 Ubiquiti Networks, Inc. All righ

Installation RequirementsThe airFiber AF-5X radio operates only with an airFiber X antenna or a converted RocketDish™ antenna.airFiber X antenna model

Hardware OverviewPort CoverLEDPanelConnects toExternal GPS AntennaChain 1: Connects to- 45° on airFiber AntennaChain 0: Connects to+ 45° on airFiber A

PortsReset ButtonManagement PortData PortManagement Port 10/100 Mbps, secured Ethernet port for configuration. In-Band Management is enabled by defau

LEDsSignal LEDsSignal 4 LED will light blue when on.Signal 3 LED will light green when on.Signal 2 LED will light yellow when on.Signal 1 LED will

Additional LEDsLED State StatusLINK Off RF OffShort Flash* SyncingNormal Flash* BeaconingLong Flash* RegisteringOn OperationalGPSOff No GPS Synchroniz

Installation OverviewWe recommend that you configure your paired AF-5X radios before site installation. Below is an overview of the installation with

2. Connect an Ethernet cable to the DATA port.3. Connect the Ethernet cable from the DATA port to the Ethernet port labeled POE on the airFiber PoE